DSM-G600, DNS-3xx and NSA-220 Hack Forum

Unfortunately no one can be told what fun_plug is - you have to see it for yourself.

You are not logged in.

#1 2010-05-24 19:01:49

slackuser
New member
Registered: 2010-05-24
Posts: 3

How to compile own kernel to DNS-313 rev A

Hi all,

I spend some time on this forum for looking for right solution how to compile own kernel. I gathered all information and my experiences and finally wrote short guideline.
http://blog.gregs.eu/?p=149

enjoy!

-greg

Last edited by slackuser (2014-02-09 22:33:43)

Offline

 

#2 2010-05-26 12:58:38

Electrocut
Member
From: France
Registered: 2009-04-05
Posts: 195

Re: How to compile own kernel to DNS-313 rev A

Great !

I used to try to build my own kernel, but the LED light never turned green.

So, till now, I was just able to build new kernel module, but always failed to completely replace the kernel.

I will try your method some day smile (I would like to turn my DNS-313 into a ipsec+l2tp VPN server, with openswan + xl2tpd)

Last edited by Electrocut (2010-05-26 13:00:54)


DNS-313

Offline

 

#3 2010-05-26 21:27:12

slackuser
New member
Registered: 2010-05-24
Posts: 3

Re: How to compile own kernel to DNS-313 rev A

Electrocut, it shouldn't be a problem to add some ipsec functionality. Unfortunately I tried to be minimalist. I added ext3, vfat, nfs and fuse support but it should be removed if you really don't use it.
I'm trying now migrate patches to 2.6.24.4. We'll see...

greg

Offline

 

#4 2012-01-17 01:58:38

malcmail
Member
Registered: 2012-01-12
Posts: 7

Re: How to compile own kernel to DNS-313 rev A

I know this thread is a long time gone but any idea how I can change these instructions for a Rev B 313? And how would I go about adding something like ipsec or similar to the kernel?

Offline

 

#5 2012-01-18 01:32:13

Electrocut
Member
From: France
Registered: 2009-04-05
Posts: 195

Re: How to compile own kernel to DNS-313 rev A

I don't think the instructions are different for Rev B. Maybe the kernel is the same.

Can you check your kernel version, by typing uname -a, and dmesg?

Mine (DNS-313 Rev A):

Code:

root@terabox:/# uname -a
Linux terabox 2.6.15 #179 Mon Nov 23 15:48:00 CST 2009 armv4l GNU/Linux
root@terabox:/#
root@terabox:/# dmesg
Linux version 2.6.15 (root@CentServer) (gcc version 3.4.4) #179 Mon Nov 23 15:48:00 CST 2009
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: GeminiA
...

Building just kernel modules is (at least for me) easier than trying to replace the kernel completely.

For VPN, openvpn will be easier than Ipsec, because you only need to build modules crc32.ko and tun.ko, there's no need to replace the kernel.

I built successfully some kernel modules for DNS-313, and posted instructions on topic Working: Openvpn 2.0.9


DNS-313

Offline

 

#6 2012-01-18 11:49:16

malcmail
Member
Registered: 2012-01-12
Posts: 7

Re: How to compile own kernel to DNS-313 rev A

Output as follows. Its a standard installation (via the Windows disk) with ffp bunged on.

Code:

root@dlink_server:/mnt/sda3/home/root# uname -a
Linux dlink_server 2.6.15 #78 Thu Jul 30 10:37:47 EDT 2009 armv4l unknown
root@dlink_server:/mnt/sda3/home/root# dmseg
-sh: dmseg: not found
root@dlink_server:/mnt/sda3/home/root# dmesg
Linux version 2.6.15 (root@Linux53) (gcc version 3.4.4) #78 Thu Jul 30 10:37:47 EDT 2009
CPU: FA526id(wb) [66015261] revision 1 (ARMv4)
Machine: GeminiA
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
  DMA zone: 16384 pages, LIFO batch:3
  DMA32 zone: 0 pages, LIFO batch:0
  Normal zone: 0 pages, LIFO batch:0
  HighMem zone: 0 pages, LIFO batch:0
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 2, 16 byte lines, 512 sets
CPU0: D cache: 8192 bytes, associativity 2, 16 byte lines, 256 sets
Built 1 zonelists
Kernel command line: root=/dev/ram0 rw mem=64M console=ttySL0,19200 initrd=0x00800000,4M ramdisk_size=4096
PID hash table entries: 512 (order: 9, 8192 bytes)
Bus: 150MHz(2/1)
Console: colour dummy device 80x30
sl2312 console setup : 
Disable IDE...config to SATA mode
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 58240KB available (1743K code, 590K data, 84K init)
Calibrating delay loop... 231.01 BogoMIPS (lpj=1155072)
Mount-cache hash table entries: 512
*** Page_chain_cachep Init!***
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4096K
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler deadline registered
Real Time Clock Driver v0.10
Gemini Gpio init
g751 init
flash probe init
Register Gemini Power control
Power event by Unknow Source 
Watchdog Timer Initialized
ttySL0 at MMIO 0x42000000 (irq = 18) is a SL2312
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
VSC-switch not found
 ---> phy_vendor = 0x1CC912
SL351x Giga Ethernet driver 0.1.6 built at Jul 30 2009 09:51:08
libata version 1.20 loaded.
sata_lepus1 version 0.1
ata1: SATA max UDMA/133 cmd 0xC4800020 ctl 0xC4800036 bmdma 0xC4800000 irq 5
scsi0 : sata_lepus1
sata_lepus0 version 0.1
ata2: SATA max UDMA/133 cmd 0xC4804020 ctl 0xC4804036 bmdma 0xC4804000 irq 4
ata2: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4123 85:7469 86:bc41 87:4123 88:407f
ata2: dev 0 ATA-8, max UDMA/133, 625142448 sectors: LBA48
HD speed:U6 (0x46)
ata2: dev 0 configured for UDMA/133
scsi1 : sata_lepus0
  Vendor: ATA       Model: WDC WD3200AAJS-0  Rev: 01.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: Attached scsi disk sda
sd 1:0:0:0: Attached scsi generic sg0 type 0
SL2312 MTD Driver Init.......
Find EN29LV400A.
Search for id:(1c 22ba) interleave(1) type(2)
Found: EN29LV400AB
SL2312 CFI Flash: Found 1 x16 devices at 0x0 in 16-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 3 MTD partitions on "SL2312 CFI Flash":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00060000 : "MTD1"
0x00060000-0x00080000 : "MTD2"
SL2312 MTD Driver Init Success ......
FTC_FOTG2XX : Init FOTG2XX Driver
Init FOTG2xx driver 
FTC_FOTG2XX : >>> Found FOTG2XX ...
pFTC_OTG c0b8d440
hcd->self.controller c0b91400
hcd end
hcd_buffer_create
ehci-hcd-FOTG2XX ehci-hcd-FOTG2XX: new USB bus registered, assigned bus number 1
usb_register_bus
ghcd_FOTG2XX hcd c0b91400
hcd_irq_For_OTG
ehci->caps->length 10, hcd->regs f6800000 , ehci->regs f6800010 
udev->state 1 
drivers/usb/host/ehci-hcd-FOTG2XX.c: USB support enabled, EHCI rev 101. 0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
FTC_FOTG2XX : >>> +FOTG2XX_get_otg_transceiver
FTC_FOTG2XX : registered host c0b91400
OTG2XX act as HOST only (don't need to wait gadget driver)
+(OTGC_Init)
pFTC_OTG->otg.default_a=1 
+(OTGC_Init)
pFTC_OTG->otg.default_a=1 
OTG_enable_VBUS 
FTC_FOTG2XX : >>> Drive VBUS ok...
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
OTG_enable_VBUS 
mdwOTGC_Control_A_VBUS_VLD_Rd 80000
+OTGP_Close()
OTG2XX act as HOST only (remove gadget function)
+OTGH_Open()(0x30=0x0)
ehci otg_set_host status 0 
FTC_FOTG200_udc_1 : Init USB device Lower driver
FOTG200_BASE_ADDRESS = 0xf6900000
******reg_val = c0422037 
FTC_FOTG200_udc_1 : ***** FOTG200 Peripheral 2.0 Test program *****
FTC_FOTG200_udc_1 : L0: System initial, Please wait...
FTC_FOTG200_udc_1 : L1: System is ready(dev->EPUseDMA=0xff)...
FTC_usb_probe_1 end
Initializing USB Mass Storage driver...
connect_change 1 
clear_bit 
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 84K
Adding 506008k swap on /dev/sda1.  Priority:-1 extents:1 across:506008k
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
EXT2-fs warning (device sda3): ext2_fill_super: mounting ext3 filesystem as ext2
Storlink egiga0 address = 14D64DA83D19
Can't find version control
GMAC-0 Addr 1 Vendor ID: 0x001cc912
Link Up (0x796d) MII Link status: 0000796d    Phy status: 0000002f
MII REG 10 = 0x7c00
 1000M/Full 
Flow Control Enable.
Storlink egiga0 address = 14D64DA83D19
Enable MAC Flow Control...
fuse init (API version 7.8)
fuse distribution version: 2.6.3
ufsd: module license 'Commercial product' taints kernel.
ufsd: driver loaded at bf00c000 built on Dec 16 2008 21:30:18
UFSD version 7.01 (Dec 16 2008, 21:21:41)
NTFS read/write support included
$Id: ufsdvfs.c,v 1.188 2008/12/04 15:52:27 shura Exp $
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
Adding 506008k swap on /dev/sda1.  Priority:-2 extents:1 across:506008k
RTC_SET_TIME::2012-01-18 09:44:15
-----------------PM0_PID 1321---------------
-----------------UbuttonPid 1306---------------

I tried the Debian install which seems to unpack OK but its definitely based on the Rev A rather than the Rev B. The problem with it is that it won't then connect to the network regardless of what I do ie fixed IP or DHCP. I've read there's a problem with connecting to a gigabit switch but had hoped the RevB may have solved this.

Offline

 

Board footer

Powered by PunBB
© Copyright 2002–2010 PunBB